Get in Toucharrow

CONTACT US

  • Name: AM5718 Development Board Cortex-A15 + M4 + DSP + PRU
  • Model: OK5718-C
  • CPU: TI AM5718
  • Architecture: Cortex-A15+M4+DAP+PRU
  • RAM: 1GB DDR3L
  • Flash: 8GB eMMC
  • Main Frequency: Cortex-A15: 1.5GHz, DSP: 750MHz, Cortex-M4: 213MHz, PRU: 200MHz
  • OS: Linux4.9.41+ QT5.6+Waylan

OK5718-C is a development board designed based on TI AM5718 processor, it consists of carrier board and SoM (system on module) and has below features

  •  ARM Cortex-A15, frequency up to 1.5GHz;
  • DSP C66x with frequency of 750MHz
  •  2x dul-core ARM Cortex-M4 with frequency of 213MHz;
  • 2x dual-core PRU with frequency of 200MHz;
  • High-speed transmission interfaces like USB 3.0, PCIe 3.0, HDMI 1.4, UART*10, QSPI*1, CAN*2, Gagibit Ethernet*2 are available and also powerful multi-media performance, wide range of applications;
  • OS options: Linux 4.9.41 + QT5.6, TI-RTOS;
  • 12-layer EINT PCB designing;
  •  the development board consists of carrier board and SoM, and the carrier board designed with 4-layer PCB and SoM with 12-layer PCB;
  • carrier board dimensions of 130*190mm, and connector hight between SoM and carrier board is just 2mm
  • SoM with 320 pins that all functions of CPU are available;
  • Industrial grade temp width: -40℃ to +85℃

PU  Ti Sitara AM5718
 Architecture

 

 Cortex-A15-1.5GHz  DSP-C66X-750MHz  2x dual-core Cortex-M4-213MHz
 2x dual-core PRU-200MHz  PowerVR SGX544 3D GPU  Vivante GC320 2D GPU
 RAM  1GB DDR3L  Flash Memory  8GB eMMC
 Dimensions  50*70mm  Connection Type  board to board connectors
 PMU  TPS659162RGZR  Voltage Input  5V
 Working Temp  -40℃ to +85℃  Relative Hummidity  10% to 90% RH none condensing
 OS  Linux4.9.41+ QT5.6+ Wayland

 

SoM FET5718-C Features
 Interface QTY  Spec.
 LCD ≤3  RGB 888
 HDMI 1  HDMI 1.4a, 1080P@60Hz;

36-bit RGB display;

HDCP encryption;

Deep color mode (10-bit, 12-bit color depth are both supported by pixel clock of 148.5MHz

 Camera ≤4  2x 8-bit DVP, up to 5.0MP

2x 8/ 16/ 24-bit DVP

 MIPI CSI-2 ≤2  CSI-2_PHY1: 1 clock lane+ 4 data lane

CSI2_PHY1: 1 clock lane+ 1 data lane

 SD/ MMC/ SDIO ≤4  1-bit or 4-bit transferring mode is supported by SD and SDIO card with UHS-I SDR104 mode (up to 104MB/s)

SD/ MMC/ SDIO1: 4-bit data

SD/ MMC/ SDIO2: 8-bit data (used as eMMC on SoM)

SD/ MMC/ SDIO3: 8-bit data

SD/ MMC/ SDIO4: 4-bit data

 USB 2  USB2.0 (up to 480Mbps), integrated with HS USB PHY
 IIC ≤5  IIC1/ 2: up to 400Kbps, standard OD

IIC3/ 4/ 5: up to 3.4Mbps, analogy OD

 HDQ1W ≤1  Support TI/ Benchmarq HDQ master device function

Comply with Dallas 1-Wire protocol

 UART ≤10  UART1: full serial interface is supported

UART3: IrDA 1.4, CIR are supported

others are standard interface

 SPI ≤4  up to 4x SPI, each with up to 4 master channel
 QSPI ≤1  work as master mode only

6 signal pins

 McASP ≤8  supports 8-ch audio at most

McASP1/2: up to 16 separate TX/ RX channel

McASP3-8: up to 4 separate TX/ RX channel

 USB3.0 ≤1  super speed USB3.0 Dual-Role-Device, Host is supported
 USB2.0 1  high-speed USB 2.0 Dual-Role-Device, Host is supported
 SATA 1  SATA Gen2
 PCIE ≤2  PCI Express 3.0 subsystem, with 2x 5-Gbps channel

1x Dual-channel interface with GEN2 standard, 2x Single-channel intgerface with Gen2 standard

 CAN ≤2  two CAN controller at most, complys with CAN2.0 protocol
 Ethernet ≤2  3-port gigabit ethernet switch subsystem provides ethernet packet communication and can be configured as an ethernet switch. It provides two network ports and available for RGMII/ RMII/ MII interface, 10M/ 100M/ 1000M adaptive
 PWMSS ≤3  supports up to 3x PWMSS, each is available for:

eHRPWM: 16-bit timer, up to 2 separate PWM output

eCAP: 32-bit timer, one channel is special for input capture pin

eQEP: rotating decode unit

 JTAG supported  standard IEEE1149.1 interface
 Keypad Port supported  9*9 keypad
 GPMC 1  8-bit/ 16-bit data bus width

up to 28-bit address bus

up to 8-bit chip selection bus

 

OK5718-C Carrier Board Features
 Interface QTY  Spec.
 LCD 1  RGB 888, supports reolution up to 1920*1080 (60Hz)
 HDMI 1  HDMI V1.4, up to 1080P 60FPS
 Camera 3  8-bit DVP OV5640, MIPI OV5640, MIPI OV5645
 Audio 1  1x MIC, 1x Phone, 2x Speaker
 USB Host 2  expended by HUB, USB 2.0 (up to 480Mbps)
 USB 3.0 1  up to 5Gbps
 USB Device 1
 Ethernet 2  10M/ 100M/ 1000Mbps, RJ-45
 WIFI 1  RL-UM02WBS-8723BU-V1.2

IEEE 802.11b/ g/ n 1T1R WLAN and Bluetooth

 BT 1
 SD card 1  compatible with SD. SDHC and SDXC (UHS-1)
 SDIO 1  drawn out by 20-pin heards with pitch of 2mm, multiplexed with SD card
 LED 2  for user’s definition to LED
 GPMC 1  general purpose memory controller bus
 QSPI 1  on-board 256Mb QSPI NOR Flash
 SPI 1
 IIC 2
 CAN 1  CAN2.0B
 UART 3  UART0 and UART1 are 5-wire serial interface, UART2 is a 3-wire interface, all are with 3.3V, each up to 5.0Mbps
 UART Debug 1  RS232, DB9 connector
 JTAG Debug 1
 HDQ 1  single line interface, on-board DS18B20
 SATA  1  SATA2, on-board 4pin D type power input connector

  • Name: AM5718 SoC based system on module
  • Model: FET5718-C
  • CPU: TI AM5718
  • Architecture: Cortex-A15 + M4 + DSP + PRU
  • RAM: 1GB DDR3
  • Flash: 8GB eMMC
  • Main Frequency: Cortex-A15: 1.5GHz, DSP: 750MHz, M4: 213MHz, PRU: 200MHz
  • OS: Linux 4.9.41+QT5.6, TI-RTOS

  • Model: OKMX6UL-C1
  • CPU: NXP(Freescale) i.MX6Ultra Lite
  • Architecture: Cortex-A7
  • RAM: 512M LvDDR3
  • Flash: 4G eMMC (8G optional)
  • Main Frequency: 528MHz
  • OS: Linux